Digitus DA-70834 Uživatelský manuál

USB 2.0 GRAPHIC ADAPTER User’s Manual DA-70833 USB 2.0 to VGA DA-70834 USB 2.0 to DVI-I

8 On Windows 7 Caution: DO NOT connect the USB display adapter to your computer before you install the provided driver. You will be instructed to d

9 2. When you see the License Agreement screen prompted as below, please click on I Accept to install the software for USB display adapter... 3.

10 4. When it is finished, the installation screen will disappear and you will return to your desktop. 5. Connect the USB display adapter to you

11 7. To control the behavior of an attached DisplayLink device (or screen), it is possible to use Windows Key+P to display a menu (and cycle throu

12 For DVI model: The equipped DVI-I (DVI-Integrated) connector transmits both the digital and analog signals. This means it supports either of the

13 3. Using the Adapter Display Properties Display Properties allows you to configuration the display mode, color quality, screen resolution, and p

14 Display Modes There is several ways you can utilize the monitor attached on the adapter. The add-on monitor can be configured to use either “mirro

15 Figure 1 Figure 2 Notice: The full DisplayLink User Interface as above is not supported on Windows 7. Displays Configuration on Windo

16 4. Drag the icons in the window at the top of the screen to match the physical arrangement of your primary monitor and add-on monitor. The add-on

17 Figure 1 Figure 2 Mirror Your Windows Desktop This mode is referred to as “mirror” or “clone” mode. In this mode, your original screen (the prim

Table of Contents 1. Introduction ... 1 Applicat

18 Manually Setting In mirror mode, the adapter will automatically select the settings (screen resolution, color quality and refresh rate) for the ad

19 Adjusting Resolution, Color Depth and Refresh Rate There are three components that make up the screen mode: Resolution: In common usage, this re

20 About the resolutions and refresh rates available to users The resolutions and refresh rates available to the user through Windows are a comprise

21 Manually Setting 1. Position the mouse anywhere on your computer desktop, r

22 4. To change the refresh rate, click Advanced… and then click Monitor. 5. Select a refresh rate from the Screen refresh rate drop-down list a

23 Standby and Hibernate, Shut Down and Restart When the adapter is connected to a computer and an external monitor, if the computer goes into standb

24 Limitation for dual adapters on Windows Vista in XDDM mode: In this mode one extended screen and one mirrored screen is supported. Only the first

25 Verifying the Driver Installation To verify your USB display adapter driver installation, please launch Device Manager by the steps below: Open

26 Uninstall the Adapter and Driver If for any reason you want to uninstall the video adapter and its driver, please take these steps: 1. Open the

27 4. Troubleshooting Q1: The display on the add-on monitor is blank. A: If the monitor power LED is green (in most cases), wait a moment for the

1 1. Introduction This USB Display Adapter enables you to connect one more monitor, LCD or projector to a computer with a USB 2.0 port. For desktop u

28 Q4: When playing the video in full screen mode, the motion is not smooth. A: Try the following tips to improve the smoothness of the movie playba

29 5. Specifications Host Interface USB 2.0 Video Interface VGA or DVI-I Connectors Video output: VGA HDDE 15pin Female Connector or DVI HDDE 29pin

30 Resolutions, Refresh rate and color depth Color Depth Resolution Name Refresh rates at 16 bit color quality Refresh rates at 32 bit color q

31 6. Regulatory Compliance FCC Conditions This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to

32 SAFETY INSTRUCTIONS Always read the safety instructions carefully: Keep this User’s Manual for future reference Keep this equipment away from

2 Applications Office workstation View your large spreadsheets across two screens with display continuity Multitask more effectively without ov

3 Package Contents Before installation, please check the items in the package. The package should contain the following items: USB Display Adapter

4 For 3 monitors, where 1 could run DVD video while also targeting productivity and business apps. Will support only 1 video of DVD resolution at f

5 2. Installation On Windows 2000 /XP/ Vista Caution: DO NOT connect the USB display adapter to your computer before you install the provided dri

6 2. Please wait while Windows configures DisplayLink Core Software. Your screens may temporarily go black or flash during this process. *Actua

7 5. After the installation is completed, you will see the DisplayLink Manager Icon in System Tray that looks like a monitor as below. Click on the